MAX31723MUA+【PDF 11/15 页】IC THERMOMETER/STAT SPI-3W 8UMAX

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录42

7页 8页 9页 10页 [11页]12页 13页 14页 15页

Digital Thermometers and Thermostats

with SPI/3-Wire Interface

as depicted in the AC Electrical Characteristics. The user

has read/write access to the R1 and R0 bits, which are

nonvolatile. See Table 4.

Serial Interface

The devices offer the flexibility to choose between two

serial interface modes. They can communicate with the

SPI interface or with a 3-wire interface. The interface

method used is determined by the SERMODE pin. When

SERMODE is connected to V

, SPI communication

is selected. When SERMODE is connected to ground,

3-wire communication is selected.

Serial Peripheral Interface (SPI)

The SPI is a synchronous bus for address and data

transfer. The SPI mode of serial communication is select-

ed by connecting SERMODE to V

. Four pins are used

for the SPI: SDO (serial-data out), SDI (serial-data in), CE

(chip enable), and SCLK (serial clock). The devices are

the slave device in an SPI application, with the microcon-

troller being the master. SDI and SDO are the serial-data

input and output pins for the devices, respectively. The

CE input is used to initiate and terminate a data transfer.

SCLK is used to synchronize data movement between

the master (microcontroller) and the slave (IC) devices.

The serial clock (SCLK), which is generated by the

microcontroller, is active only when CE is high and dur-

ing address and data transfer to any device on the SPI

bus. The inactive clock polarity is programmable in some

microcontrollers. The devices offer an important feature

in that the level of the inactive clock is determined by

sampling SCLK when CE becomes active. Therefore,

either SCLK polarity can be accommodated. Input data

(SDI) is latched on the internal strobe edge and output

data (SDO) is shifted out on the shift edge (see Table 5

and Figure 7). There is one clock for each bit transferred.

Address and data bits are transferred in groups of eight,

MSB first.

Table 3. Configuration/Status Register Bit Descriptions (continued)

Table 5. Function Table

Table 4. Thermometer Resolution

Configuration

Note: CPHA bit polarity must be set to 1.

*CPOL is the clock polarity bit that is set in the control register of the microcontroller.

**SDO remains at high impedance until 8 bits of data are ready to be shifted out during a read.

BIT 2

R1: Thermostat resolution bit 1. Factory power-up state = 0 and is stored in nonvolatile memory. Sets the con-

version resolution (see Table 4).

BIT 1

R0: Thermostat resolution bit 0. Factory power-up state = 0 and is stored in nonvolatile memory. Sets the con-

version resolution (see Table 4).

BIT 0

SD: Factory power-up state = 1. The user has read/write access to the SD bit, which is stored in nonvolatile

memory.

0 = The devices continuously perform temperature conversions and store the last completed result in the tem-

perature register.

1 = The conversion in progress is completed and stored, and then the devices revert to a low-power shutdown

mode. The communication port remains active.

THERMOMETER

RESOLUTION (BITS)

MAX CONVERSION

TIME (ms)

100

200

MODE

SCLK

SDI

SDO

Disable reset

Low

Input disabled

High impedance

Write

High

CPOL = 1*, SCLK rising

Data bit latch

High impedance

CPOL = 0, SCLK falling

Read

High

CPOL = 1, SCLK falling

Next data bit shift**

CPOL = 0, SCLK rising

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式